Bercomac 700370 Uživatelský manuál

1 OWNER’S MANUAL Model Number BERCO Subframe for JOHN DEERE SERIES 300, LX, GT, GX and G-100 WITH FOOT LIFT OR MANUAL HAND LIFT Tractors 106446

8 ASSEMBLY Install mounting pins IF YOUR TRACTOR IS NOT EQUIPPED WITH MOUNTING PINS: Remove the bolt that holds the left hand side mower lift arm (it

9 ASSEMBLY SUBFRAME INSTALLATION: Slide the subframe under the tractor between the front and back wheels on the left side. Lift the back part of the s

10 Replace front supports SUBFRAME PREPARATION FOR THE JOHN DEERE TRACTORS MODELS: GT325, 335, 345, 355 GX 325, 335, 345, 355 IMPORTANT: TORQUE A

11 ASSEMBLY Install handle support Install the handle support (item 1) on the left hand side with a 3/8 x 1 1/4" hex bolt (item 2) and flange nu

12 ASSEMBLY Install lift arm Install the lift arm (item 1) to the lift arm extension (item 2) with two 5/16 x 3/4" bolts and flange nuts. Tighte

13 ASSEMBLY Remove the bolt that holds the left hand side mower lift arm (item 1). Reinstall the lift arm by inserting (as shown) the mounting pin (it

14 ASSEMBLY Install lift arm Install the lift arm (item 1) to the lift arm extension (item 2) with two 5/16 x 3/4" bolts and flange nuts. Tighte

15 ASSEMBLY Lower the tension arm (item 1) to release the tension on the helper spring (item 2) to facilitate snowblower installation. Install the s

16 ASSEMBLY Remove the belt guard from the back of snowblower. Move the tension arm (item 8) towards the back to facilitate the belt installation. I

17 ASSEMBLY Insert the handle (item 1) into the support (item 2) as shown. Install the hook (item 3) on the rotation worm (item 4). Insert the hook

2 LIMITED WARRANTY Bercomac Limitée 92, Fortin Nord, Adstock, Québec, Canada, G0N 1S0 Conditions and Products Covered: BERCOMAC guarantees any part o

18 ASSEMBLY Lower the arm (item 1) to release the tension on the helper spring (item 2) to facilitate rotary broom installation. Attach the

19 ASSEMBLY Install the belt as shown. Apply tension on the belt by moving the tension arm (item 8) towards the front. And secure with a 3mm hair pi

20 ASSEMBLY VERIFY TIRE PRESSURE: Check and adjust tractor tire pressure as follows: Front tires: 20-25 psi Back tires: 8-10 psi Tire pr

21 ASSEMBLY Lower the arm (item 1) to release the tension on the helper spring (item 2) to facilitate blade installation. UTILITY BLADE INSTALLATION:

22 Insert the handle (item 1) into the support (item 2) as shown. Install the handle (item 1) on the control rod (item 3) as shown and secure with a

23 MAINTENANCE & DISMOUNTING WARNING TO PREVENT INJURIES: Stop the motor. Apply parking brakes. Remove the ignition key. Disconnect the wire f

24 PARTS BREAKDOWN PUSH FRAME 700370-3

25 PARTS LIST PUSH FRAME 700370-3 O/L = Obtain locally Ref. Réf. English description Description française Qty. Qté. Part # Pièce # 1 Pivot support

26 PARTS BREAKDOWN SUBFRAME 700370-3

27 PARTS LIST SUBFRAME 700370-3 Ref. Réf. English description Description française Qty. Qté. Part # Pièce # 1 Right subframe flat bar Fer plat dr

1 INTRODUCTION ...

28 Ref. Réf. English description Description française Qty. Qté. Part # Pièce # 26 Mounting pin Goupille de montage 2 102257 27 Adjusting rod T

29 TORQUE SPECIFICATION TABLE GENERAL TORQUE SPECIFICATION TABLE USE THE FOLLOWING TORQUES WHEN SPECIAL TORQUES ARE NOT GIVEN NOTE: These values

30 ATTACHMENTS ROTARY BROOM /#700316-1 with polypropylene brush. Fits on same subframe as snowblower & utility blade. Requires an adaptor. UTIL

31 NOTES ____________________________________________________________________________________________________________________________________________

32 NOTES ____________________________________________________________________________________________________________________________________________

33 NOTES ____________________________________________________________________________________________________________________________________________

34 WHEN PERFORMANCE & DEPENDABILITY ARE NON NEGOTIABLE ! Bercomac Limitée 92, Fortin North, Adstock, Quebec, Canada, G

2 INTRODUCTION TO THE PURCHASER This new attachment was carefully designed to give years of dependable service. This manual has been provided to ass

3 SAFETY PRECAUTIONS TRAINING This symbol, "Safety Alert Symbol", is used throughout this manual and on the attachments safety labels to wa

4 SAFETY PRECAUTIONS WHENEVER YOU SEE THIS SYMBOL IT MEANS: WARNING! BECOME ALERT ! YOUR SAFETY IS INVOLVED! WARNING FOR YOUR SECURITY: Read

5 ASSEMBLY Install the mounting pins IF YOUR TRACTOR IS NOT EQUIPPED WITH MOUNTING PINS: Remove the bolt that holds the left hand side mower lift arm

6 Install handle support ASSEMBLY Install the handle support (item 1) on the left hand side with a 3/8 x 1 1/4" hex bolt (item 2) and flange nut

7 ASSEMBLY Install lift arm Install the lift arm (item 1) to the lift arm extension (item 2) with two 5/16 x 3/4" bolts and flange nuts. Tighten